How To Build A Wooden TV Stand?

Table of Contents

How To Build A Wooden Tv Stand?

Easy-To-Build TV Stand
Create a trendy home for your tv with this straightforward, fine-looking stand. It offers an area for an oversized flat-screen TV and has extra area for elements. Plus, there’s further area that you just will use to deal with speakers or to show a number of your favorite things.

Materials
Wood merchandise
4Board , 1×2 X 96″
1Board , 2×2 X 96″
2Board , 1×6 X 96″
1Board , 1×6 X 72″
2Board , 1×8 X 96″
1Plywood , 3/4″ X 24″ X 48″
1Plywood , 1/4″ X 24″ X 24″

Hardware & provides
1001 1/4″ Coarse-Thread Kreg Pocket-Hole Screws
201-1/4″ 18-Gauge Brad Nails
Cut List & components
4Front/Back Rail , 3/4″ X one 1/2″ X 54″
4End Rail, 3/4″ X one 1/2″ X twelve 1/2″
4Leg , one one/2″ X 1 1/2″ X 22″

Directions

These free DIY TV stand plans can assist you to build not solely an area to take a seat on your TV but conjointly an area to store your connected devices and media. You will even get to try and do it in your own vogue, their area unit plans for a house, rustic, modern, modern, and industrial tv stands.

1 Create The Rails
Cut four Front/Back Rails and 4 finish Rails to length from 1×2 boards, as shown within the cutting diagram. along with your Kreg®, Pocket-Hole Jig started for 3/4″-thick material, drill pocket in these Rails holes wherever shown. Sand the Rails swish.

2 Cut Legs And Assemble
Cut four Legs to length from a 2×2 board, as shown within the cutting diagram. Then, attach the Rails to the Legs, as shown, exploitation one 1/4″ coarse-thread Kreg Pocket-Hole Screws.

3 Produce The Highest Slats
Cut 3 prime Slats to length from 1×6 boards, as shown within the cutting diagram. Drill pocket holes in these items, as shown.

4 Assemble The Highest
Join the highest boards along exploitation one 1/4″ coarse-thread Kreg Pocket-Hole Screws to form a panel, as shown. Sand the highest assembly pro re nata to free the wood and also the joints between the Slats.

5 Produce The Bottom Slats
Cut 2 Base Slats to length from 1×8 boards, as shown within the cutting diagram. along with your pocket hole jig started for 3/4″ material, drill pocket holes in these items, as shown. employing a jigsaw, notch 2 corners of every Base Slats, as well.

6 Assemble The Bottom
Join the bottom boards along exploitation one 1/4″ coarse-thread Kreg Pocket-Hole Screws to form a panel, as shown. Sand the bottom assembly pro re nata to free the wood and also the joints between the Slats.

7 Create The Shelves
Cut 2 Wide Shelf Slats to length from 1×8 boards, and cut 2 slim Shelf Slats to length from 1×6 boards, as shown within the cutting diagram. Then combine up a slim and Wide Slat to form every shelf, and drill pocket holes as shown.

8 Assemble The Shelves
Join a slim Shelf Slat to a good Shelf Slat exploitation one 1/4″ coarse-thread Kreg Pocket-Hole Screws to form a panel, as shown. Repeat this to form the opposite shelf assembly. Sand every shelf assembly.

9 Install The Highest And Base
Attach the highest and Base to the stand by driving 1-1/4″ coarse-thread Kreg Pocket-Hole Screws into them from beneath. once attaching the highest, confirm it overhangs the stand equally on all sides. confirm the bottom has consistent gaps around the legs.

10 Create The Dividers
Cut 2 Dividers to the dimensions from 3/4″ laminate, as shown within the cutting diagram. along with your Kreg Pocket-Hole Jig started for 3/4″-thick material, drill pocket holes in one face of every Divider, as shown. Then Drill shelf-pin holes, as shown. A Kreg Shelf Pin Jig makes it best to urge consistent spacing and straight holes, therefore you’ll have wobble-free shelves.

11 Create Trim And Install The Dividers
Cut 2 Divider Trim items to size from a 1×2 board, as shown within the cutting diagram. currently attach the Dividers, wherever shown, by driving one 1/4″ coarse-thread Kreg Pocket-Hole Screws into the highest Slats and Base Slats. confirm the Dividers area unit straight and sq. before you drive the screws. Then nail on the Divider Trim items so that they overhang the Divider equally on all sides.

12 Produce A Back Panel
Cut a Back Panel to size from 1/4″ laminate, as shown within the cutting diagram. Then drill 3 holes for wires to meet up with, as shown.

13 Keep Mum The Rear
Attach the rear by nailing it to the rear edges of the dividers with 1-1/4″ brad nails. Do any final sanding that’s required, then add paint or end you prefer to complete your TV stand. we have a tendency to use a grey stain.

10 Best Wooden TV Stand With Drawers And Shelves

Leave a Reply

Your email address will not be published. Required fields are marked *

error: Content is protected !!